登录
首页 » matlab » 1dFDTD

1dFDTD

于 2006-05-29 发布 文件大小:1KB
0 231
下载积分: 1 下载次数: 29

代码说明:

  需要解压缩后将程序复制到MATLAB的M文件,然后运行使用(decompress will need to copy the documents MATLAB M, and then run the use of)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • LMsarsem_panel
    本函数用于面板空间滞后模型SAR及空间误差SEM模型的LM检验,提供稳健统计值。( Computes (robust) LM tests for spatial lag and spatial error)
    2015-01-22 21:49:05下载
    积分:1
  • shuxuejianmoMATLAB
    数学建模时常用的matlab编码,对建模中出现的问题很有效(Commonly used mathematical modeling matlab coding, modeling the problems in a very effective)
    2013-12-15 17:33:31下载
    积分:1
  • zerodig
    Matlab/simulink 搭建的输电线路距离保护,零度接线方式的仿真模型(Distance protection of transmission lines Matlab/simulink to build the simulation model, the zero connection mode)
    2014-06-09 16:55:08下载
    积分:1
  • 37313541StrainStressAnaFEACodes
    基于matlab的波的传播shuzhi模拟(Wave propagation simulation based on matlab)
    2017-01-16 15:18:16下载
    积分:1
  • MATLABIIR
    这篇文章说明了如何在Matlab环境下利用FDA 工具包来进行IIR滤波器的设计(脮芒脝 陋 脦脛脮脗脣渭脙 梅 脕脣脠莽 潞 脦脭脷Matlab 禄戮 鲁 脧脗脌没脫脙FDA 鹿 陇 戮 脽 掳 眉脌 )
    2008-07-10 11:07:06下载
    积分:1
  • matlabText
    说明:  matab 开发环境下写的一个图像处理程序,此程序基于MATLAB图书馆索引号的自动识别(matab development environment to write an image processing program, this program is based on MATLAB library index number of the Automatic Identification)
    2011-04-14 16:26:49下载
    积分:1
  • RMLE_system_identification_matlab
    使用递推极大似然估计法辨识系统参数,这是《系统辨识》这门课程的程序,希望大家(特别是上这门课需要写论文的同学)能够用得上(Using maximum likelihood estimation method recursive identification system parameters, this is the " system identification" procedure for this course, I hope you (especially on this course requires students to write papers) to the lingua franca of)
    2011-06-24 23:33:52下载
    积分:1
  • Generator-for-Wind-Turbine
    DEscription of Double fed Wind Turbine
    2014-09-05 02:25:12下载
    积分:1
  • data
    数字信号处理的MATLAB实现,书中附带的程序代码(Digital signal processing implementation of MATLAB, the book attached to program code)
    2009-03-10 21:31:30下载
    积分:1
  • BatchSimulation
    As we know, the energy needed for sensors should be electrical. So the rst step before start to work is to convert environmental energy to electrical one. Inside the node there are dierent components for sensing the area, collecting data and processing the data. So the main dierent part of this kind of nodes, in compare of WSN nodes, is the power part. Once the stored energy reach to a certain amount, the power supply for micro controller and transceiver will start to work. They will continue to work until they have energy, as soon as the energy nish, they stops and energy storage device start to work to save energy again. The other fact should be consider about EH-WSN node is that the available energy can change in dierent nodes. So every node has its own harvesting rate.
    2013-07-20 14:34:56下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载