Applied-Optimization-with-Matlab

主要是vblast的检测算法的研究，主要讲的是检测算法的分析，非常有用(Mainly vblast test algorithm, the main stress is the detection method of analysis, very useful)

matlab经典算法的程序,里面有详细的目录文件。(some classical algorithm programs of Matlab)

ZStackAPI2007 ZStackAPI2007

说明：  这里介绍了一种基于自适应滤波的噪声抵消法，采用归一化最小均方误差算法，采集实际噪声环境下各种不同信噪比的带噪语音样本进行降噪处理，实验结果表明，处理后信号的信噪比得到了较大程度的提高，大大改善了听音效果，具有很高的可懂度，且语音自然度好，没有失真；并与谱减法进行了比较，自适应噪声抵消法的降噪幅度比谱减法有一定提高，在听音效果上，用自适应噪声抵消法处理后的语音在清晰度，自然度方面优于谱减法。(Here a novel adaptive noise cancellation method using normalized least mean square algorithm, collecting a variety of actual noise environment, the SNR of noisy speech samples for noise reduction, experimental results show that treatment After the signal to noise ratio was greater improvement in the level, greatly improved the listening results, with high intelligibility and naturalness of speech is good, no distortion and were compared with the spectral subtraction, adaptive noise cancellation law than the spectral subtraction noise reduction rate of a certain improvement in the listening results, and with the adaptive noise cancellation method in the treatment of voice clarity, naturalness is better than spectral subtraction.)

首先在m脚本文件canshuo.m中输入节点个数和路径权重，在命令窗口中输入canshu，用s=12,e=10的格式输入要求的起止点，再输入main即可得到两点之间的路径和长度。(M script file canshuo.m first enter the node number and the right path lies in the command window enter canshu, with s = 12, e = 10 The format of the input requirements of the start and end points, and then enter the main between two points can be obtained path and length.)

盲信号分离的matlab程序，很好很实用，你值得拥有！(This program is made by Matlab 7.0.It is very good.you can prosess it )

高分辨率雷达 距离向压缩算法滤波器设计 三种方法 全面设计(clc clear all close all 2013年9月28日 ---------------参数---------- Tr=42e-6 fs=9.5e6 K=0.7e11 Nfft=2048 -------------匹配滤波 时域生成-------------- t=(-Tr/2+1/fs:1/fs:Tr/2-1/fs) w = kaiser(length(t),2.5) w=w w = ones(1,length(t)) ht1=w.*exp(-1i*pi*K*t.^2) ht2=w.*exp(1i*pi*K*t.^2) hf1=fft(ht1,Nfft) hf2=fft(ht2,Nfft) figure subplot(211) plot(abs(hf1)) title( 匹配滤波器1 幅频响应 ) subplot(212) plot(phase(hf1)) title( 匹配滤波器1 相位 ) figure subplot(211) plot(abs(hf2)) title( 匹配滤波器2 幅频响应 ) )

列主元消去法解线性齐次方程组的matlab程序(Column principal component elimination method for solving linear homogeneous equations matlab program)

实现了向量的聚类算法，输入三个参数：向量集合、划分数目和设定的阈值，就可得到聚类结果，以欧式距离作为距离判别准则。(Realize the vector of the clustering algorithm, the input three parameters: vector set and the division of number and set threshold, can get clustering results to the Euclidean distance as a criterion for distance. )

是一个关于OFDM仿真的小程序，比较小的程序，可以拿来练练手(It is a little on the OFDM simulation program is relatively small program that can be used to practice your hand)