BLDCM

说明：  遗传算法 求解单目标问题，采用二进制编码（matlab)(using genetic algorithm to optimize Single-objective function)

M.Jankiram chapter 2 on MIMO

它可以实现对jpg图像进行人脸检测，最后对原彩色图像中人脸的位置以方框形式显示(It can realize JPG image of face detection, finally to the original color image face position shown in box)

Matlab algorithm genetic implementation

说明：  细分曲面catmullClark细分算法代码，直接运行的结果为一个实例的细分结果(subdivision surface)

优秀论文及配套源码。Hilbert-Huang变换(HHT)是一种新的非平稳信号处理技术，该方法由经验模态 分解(EMD)与Hilbert谱分析两部分组成。任意的非平稳信号首先经过EMD方法处理后被分解为一系列具有不同特征尺度的数据序列，每一个序列称为一个固有模态函数(IMF)，然后对每个IMF分量进行Hilbert谱分析得到相应分量的Hilbert谱，汇总所有Hilbert谱就得到了原信号的谱图。该方法从本质上讲是对非平稳信号进行平稳化处理，将信号中真实存在的不同尺度波动或趋势逐级分解出来，最终用瞬时频率和能量来表征原信号的频率含量。 本文研究了基于HHT的暂态电能质量扰动检测方法，介绍了HHT的基本原理和利用HHT检测电能质量多扰动信号的实现方法。仿真试验表明该方法可以实时检测扰动的起止时刻，持续时间和扰动幅度，适用于电能质量多扰动的监测和辨识系统。 (Hilbert-Huang Transform(HHT) is a new non-stationary signal processing technology，including the Empirical Mode Decomposition(EMD) and Hilbert spectral analysis．In this method，arbitrary non-stationary signals was divided into a series data sequence with different characteristic scales after the first EMD treatment，each sequence is called an intrinsic mode function(IMF)，and then each IMF component gained corresponding the Hilbert spectrum though Hilbert spectrum analysis，a summary of all Hilbert spectrum assembled to the spectra of the original signal．In essence，this method is a stable processing for non-stationary signal，which decomposed the different fluctuations or trends in the signal in rum，and represented the frequency content of the original signal using the final instantaneous frequency and energy． This paper study a method to detect power quality disturbances based on the HHT，in which the principle and the realization of the HHT and the realization of power quality disturbance)

Function to generate colored noise using Euler-Maruyama method

This m files and Gui files are for solve the problem about Find specific position in 3D space. by using 3d circles you can axis in 3d spaces except one situation explaned as not selected axis x,y,z if you want to know more about seek the position in 3D spaces than depress the zip file and operate m file named Robot_report1 and Robot_report1.fig

编写一个含QAM传输的发送和接收模块 1)分别采用复基带仿真和实带通仿真两种形式 a) 实带通仿真时, 载波频率为符号率的4倍 b)发端采用滚降系数0.5的根号升余弦滤波器 2)画出Eb/N0=15dB时的接收波形(收滤波前),取100个采样 3)画出发端输出的眼图和收端过匹配滤波后的眼图(画眼图时不加噪声) 统计误符号率和误比特率与Eb/N0的关系,画出曲线, 与理论计算的曲线相对比 (Prepare to send of one with QAM transmission and receiver module 1), respectively, the complex baseband simulation and the real band-pass simulation in two forms a) the real band-pass simulation, the carrier frequency used for the symbol rate of 4 times b) the originator roll-off factor of 0.5 root raised cosine filter, 2) draw Eb/N0 = 15dB when the received waveform (closing filter), take 100 samples) to draw the originator of the output eye diagram and income side of the eye diagram after the matched filter ( draw the eye diagram without noise) statistics symbol error rate and bit error rate and Eb/N0, draw a curve calculated with the theoretical curve compared)

writing fast matlab code