Arnold000

MATLAB的迭代静校正代码，原创……………………(MATLAB iterative static correction code, original ... ... ... ... ... ... ... ...)

iir低通滤波器设计实验代码，可以清楚地观察到滤波效果(iir low-pass filter design experimental code, can be clearly observed filter effect)

该程序适用于实现匹配滤波器的基于MATLAB编写(matchfilter)

读取视频，检测并标记白色车辆目标，去除车道线和其他非圆碟形状的结构目标物，最后播放可视化后的视频(It will read the video, detect and mark vehicle targets,then lane and other targets of non-circles shape will be removed, at last,play the video after visualization.)

说明：  根据前人研究成果可以证明，煤镜质组反射率各向异性对煤田构造特征具有指示意义，镜质组最小反射率可以指示构造主应力方向。然而，在实际测量中，如何得到真正的镜质组最大、最小反射率及其方位是其中的关键环节。利用现有的岩石有限应变椭球拟合方法进行镜质组反射率椭球体拟合不失为一种行之有效的方法，可以由此确定镜质组最大、最小、中间反射率及其三维空间方位。 将之前拟合得到的反射率椭圆看作岩石有限应变椭圆即二维应变，其由之前的统计方法测定得到，三个截面的数据对于拟合唯一应变椭球来说是过多的，因此不可避免出现误差，导致三个截面应变椭圆不通过同一个椭球的情况。为了从三个截面数据得到唯一的应变椭球，需要对得到的数据进行相容性调整。采用Oertel的方法，从每一测量参数在不同截面中的值是正态分布这一假定出发，利用加权最小二乘法进行误差调整。(According to results of previous studies may prove vitrinite reflectance anisotropy on structural characteristics have implications for coal, vitrinite reflectance may indicate tectonic minimum principal stress directions. However, in actual measurement, how to get real vitrinite maximum, minimum reflectivity and its orientation is the key link. Conduct vitrinite reflectance ellipsoid fitting regarded as a proven method using existing rock finite strain ellipsoid fitting method can thus determine vitrinite maximum, minimum, intermediate reflectance and dimensional spatial orientation . Before fitting the reflectance of finite strain ellipse oval rock that is seen as a two-dimensional strain, as determined by statistical methods which have been before the data fit only for the three sections of the strain ellipsoid is excessive, and therefore can not to avoid errors, resulting in three elliptical cross-section does not pass through the same strain ellipsoid situation. In order to obtai)

ctp海风实例 有修改 非常好的交易实例(ctp cthostftdctraderapi)

Predictive direct power control (P-DPC) applied to voltage source pulse-width-modulation (PWM) rectifier was introduced in this paper. Based on the model of power prediction, voltage vectors were selected according to minimizing power errors in a fixed time interval, which results in a constant switching frequency control for P-DPC. It simplifies the implementation of P-DPC procedure by selecting switching states based on the principle of space vector modulation (SVM). In order to eliminate power errors caused by control delay, a detailed control delay compensation scheme was designed. Experimental results based on a 2kW prototype were presented, which showing that P-DPC has a faster power response compared to standard voltage-oriented-control (VOC) techniques. Besides, the dynamic performance of the system is also improved significantly by control delay compensation.

Code in matlab about processing signals

it is about ldpc codes

利用matlab的lpc function 實做出將input source音檔算出其coefficent and gain並由上述資料可以重新合成還原音訊(The lpc function using matlab real audio file to make the input source is calculated by its coefficent and gain reduction above information can be re-synthesized audio)