workkalmanfilter5

经典的DOA算法的MATLAB仿真程序，可用于仿真与改进算法进行对比(classical DOA MATLAB )

基于光正交码构造了一类新的不规则00c—LDPc码．新的LDPC码是准循环码，其编码复杂度与码长成 线性关系，具有编码复杂度低的特点，它所对应的双向图中没有四线循环．用和积译码算法对新的码字进行了仿 真，结果表明，与具有类似参数的随机码和规则OOc—LDPc码相比，当信道误码率为10。5时，译码增益分别为 0．3和0．15 dB．(Construct a new class of irregular the 00c-LDPc code based on optical orthogonal codes. LDPC codes are quasi-cyclic code, its complex coding with code length linear relationship, with low encoding complexity, the corresponding bidirectional Figure it in four-wire loop. Simulation with integrated decoding algorithm of the new code word, the results show that when the channel bit error rate, compared with the random codes with similar parameters and rules OOc-LDPc code decoding gain were 10.5 0.3 and 0.15 dB.)

本文基于马赫-泽德干涉结构的分布式光纤传感系统，采用模式识别的思想，详细论述了信号特征辨识和提取方法，提高了定位准确度，减少了误报！(Based on Mach- Zehnder interferometer structure of the distributed optical fiber sensing system, using pattern recognition idea, discussed in detail the signal feature recognition and extraction methods to improve the positioning accuracy and reduce the false alarm!)

lvq 算法 关于读取一个手写字体的数据库的代码的问题[图像图形(Identification of data sets, can be used as, the classification of experimental data. Category: Pattern Recognition)

麻省理工大学 电气工程与计算机科学系 信号与系统专业关于matlab的应用(Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science, Signals and Systems professional application on matlab)

Arduino Uno Sketch to take measurements a strain gauge at precise depths into an elastic object. Interfaces the Uno with a micrometer using SPC and with strain gauge bridge circuit using Analog input pin. Tested to work on OSEPP Uno R3 Plus (Arduino Uno equivalent uC)

matlab dsp building fpga(matlab dsp building )

WSN 质心定位算法 Centorid Algorithm 加经典参考文献 A: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 未知节点利用邻居锚节点进行定位，没有邻居锚节点的未知节点无法定位。 B: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 未知节点一旦被定位就充当起锚节点的功能，向周围邻居发送自己的估计坐标信息 未知节点把已经定位的未知节点与锚节点同等对待 C: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 有邻居锚节点的未知节点只利用邻居锚节点进行定位，没有邻居锚节点的未知节点才利用已经定位了的邻居未知节点进行定位。(WSN centroid localization algorithm Centorid Algorithm A: If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Unknown node using the neighbor anchor nodes to locate, no neighbors anchor nodes and unknown nodes can not be located. B:   If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Unknown nodes are positioned on as soon as the function of anchor nodes to send their neighbors estimated coordinate information Unknown unknown node to node already positioned anchor nodes treated equally C: If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Of the unknown neighbor anchor node the neighbor nodes are only positioned anchor nodes, )

Clark变换与Inv_Clark变换，引入输入信号进过测试能够实现功能(Clark and Inv_Clark)

关于信号处理方面的内容，在matlab编程实现时详细解答(Signal processing on the content of programming in matlab to answer in detail)