12_Commandes_et_fonctions_de_Matlab

analogue model of full bridge rectifer, for high validating pfc

详细介绍了PSO算法的实现过程！keshiixangezhongliziqunsuanfa!(PSO algorithm was introduced in detail the implementation of the process!)

本程序是针对UCI图像数据集上的图像进行重构与识别的实验(This procedure is for the UCI data sets on the image to reconstruct the image and recognition of the experiment)

在此代码所使用的算法是从以下引用： S Gillijns等人“什么是集合卡尔曼滤波和它工作得如何？“ 2006年美国电力系统及其控制会议，明尼阿波利斯，美国明尼苏达州六月14-16，2006，页4448-4453。(The algorithm used in this code is referenced from the following: S Gillijns et al "What Is the Ensemble Kalman Filter and How Well Does it Work?" Proceedings of the 2006 American Control Conference, Minneapolis, Minnesota, USA, June 14-16, 2006, pp 4448-4453.)

刘金琨教授编写的智能控制第二版的配套源程序(Professor Liu Jinkun written in intelligent control of the second version of the matching source)

simulation QPSK on fading channel with convulation code

1.题目：数字滤波器的设计与应用 2.设计要求：利用 Matlab 软件,以复合信号分离为例,对 “数字信号处理” 课程中 的谱分析 、数字滤波器设计和信号滤波这三个过程进行了仿真实现,给出了仿真结果。 3.具体步骤： （1）构造原始信号s(t) （2）画出s(t)的频谱 （3）设计ellipse数字滤波器(IIR)，包括低通，带通，带通，并显示幅频特性 （4）用得到的滤波器进行滤波，分离出三路信号，观察时域波形和幅频特性 （5）用三路信号s1,s2,s3尝试重新合成原始信号 4.问题：为什么重新合成的信号和原信号不相等呢？谁能解释一下？谢谢,QQ:664519036( 1. Title: Digital Filter Design and Application 2. Design requirements: use of Matlab software to composite signal separation, for example, on "Digital Signal Processing" course Of the spectral analysis, digital filter design and signal filtering process carried out three Simulation, the simulation results. 3. Concrete steps: (1) construct the original signal s (t) (2) Draw s (t) of the spectrum (3) design ellipse digital filter (IIR), including low pass, band pass, band pass, and shows amplitude-frequency characteristics (4) filtering with a filter obtained by the isolation of three signals, observed time-domain waveform and frequency characteristics (5) with a three-way signal s1, s2, s3 try to re-synthesis of the original signal 4. Question: Why is re-synthesized signal and the original signal is not equal to it? Who can explain? Thank you, QQ: 664519036)

香农编码 采用matlab编程实现 的程序代码(Shannon coding using matlab programming code)

基于Matlab的车牌识别程序，是我自己做的，不是特别好，但基本框架已做好，还有word报告。(Matlab-based license plate recognition program, is my own, not particularly good, but the basic framework has been doing a good job, there is word report.)

Most of the algorithms presented in the literature and in this chapter are basically intuitive and are intended to work with ECG signals in accepted clinical conditions, i.e. SNR higher than 18 dB.