QPSK

STM32F407驱动SPI屏幕，采用的是模拟SPI(STM32F407 drives SPI screen, using simulated SPI)

基于stm32f407的sd卡数据读写功能，源码数据(Based stm32f407 the sd card data read and write functions, source data)

ds1302液晶时钟液晶时钟及温度检测程序(the ds1302 LCD Clock LCD Clock and temperature testing procedures)

IN PSCAD THE DESING OF THE VARIABLE TYPE WIND FARM

单片机驱动数模转换器ADC0809的接口程序员(Single-chip driver DAC ADC0809 interface programmers)

嵌入式开发校验最全C源码，包括（CRC8、CRC16查表法及算术法校验、异或和校验、和校验、校验和补码等）、校验工具，校验文档。全部为工程实际项目本人使用的源代码。( Embedded developers the most complete C source code verification, including (CRC8, CRC16 checksum table method and arithmetic method, XOR and parity, and parity, parity, and complement, etc.), calibration instruments, calibration documentation. All actual project I used for the project s source code.)

说明：  本实验开机后，先初始化MPU6050，然后利用DMP库，初始化MPU6050及使能DMP，最后，在死循环里面不停 读取：温度传感器、加速度传感器、陀螺仪、DMP姿态解算后的欧拉角等数据，通过串口上报给上位机（温 度不上报），利用上位机软件（ANO_Tech匿名四轴上位机_V2.6.exe），可以实时显示MPU6050的传感器状 态曲线，并显示3D姿态，可以通过KEY0按键开启/关闭数据上传功能。同时，在LCD模块上面显示温度和欧拉 角等信息。DS0来指示程序正在运行。另外,本例程也可以通过USMART调用MPU_Read_Byte/MPU_Write_Byte 等函数,来实现对MPU6050寄存器的读写操作(仅在UPLOAD OFF状态下).(This experiment starts with initializing MPU6050, then using DMP library, initializing MPU6050 and enabling DMP. Finally, it keeps on in the dead cycle. Read: temperature sensor, accelerometer, gyroscope, Euler angle after attitude calculation of DMP and other data, report to PC through serial port (temperature). The sensor of MPU6050 can be displayed in real time by using the upper computer software (ANO_Tech anonymous four-axis upper computer_V2.6.exe). The state curve and 3D posture can be displayed, and the data upload function can be turned on/off by KEY0 button. At the same time, temperature and Euler are displayed on the LCD module. Angle and other information. DS0 to indicate that the program is running. In addition, this routine can also call MPU_Read_Byte/MPU_Write_Byte through USMART Equivalent function to achieve the read-write operation of MPU6050 registers (only in UPLOAD OFF state).)

单片机在电冰箱智能模糊控制中的应用(SCM in refrigerators Intelligent Fuzzy Control System)

单片机C语言程序设计实训100例——基于8051+Proteus仿真(Microcontroller C Programming Language Training 100 cases- based 8051+Proteus simulation)

包含大量的汇编单片机的编程，对汇编语言有一定的要求，为学习C语言的提供一定汇编基础(Contains a large amount of assembly SCM programming, to ask for a certain assembly language, to learn the language C provides certain assembly basis )