atlab

一系列包含串口、Modem、收发传真、终端仿真等方面的编程例子( A series of contains aspect the and so on string mouth, Modem, receiving and dispatching facsimile, terminal simulation programming example )

说明：  5. 在三条径的瑞利信道中，对于直接序列扩频： (1) 请设计DS-CDMA一种具体的码分导引辅助的信道估计方法，接收机分别采用等均益合并、最大比合并。用Simulink进行仿真，画出比特信噪比与信道估计均方误差的关系曲线和比特信噪比与误码率的关系曲线。 (2) 设频率已经同步，请设计DS-CDMA一种具体的单停顿滑动相关时间同步方法，用Simulink进行仿真，画出比特信噪比与捕获概率的关系曲线。 (3) 设时间已经同步，请设计DS-CDMA一种具体的频率同步方法，用Simulink进行仿真，画出比特信噪比与频率同步误差的关系曲线。(5. In three-path Rayleigh channel, for direct sequence spread spectrum: (1) please design a specific code division navigation aided channel estimation method for ds-cdma, and adopt equal-beneficial combination and maximum ratio combination for receivers respectively.Simulink is used to simulate and draw the relationship curve between bit SNR and channel estimation mean square error and the relationship curve between bit SNR and bit error rate. (2) assuming that the frequency has been synchronized, please design a specific single-stop sliding correlation time synchronization method ds-cdma, Simulink simulation, draw the relationship between the bit SNR and the acquisition probability curve. (3) if the time has been synchronized, please design a specific frequency synchronization method ds-cdma, Simulink simulation, draw the relationship between the bit SNR and frequency synchronization error curve.)

采用labview编写的I2C通信程序，几乎可以通用的喔(prepared by the I2C communications procedures, almost generic oh)

labwindows CVI 8.0 下调试通过的gprs，建立过程和udp通讯。(with labwindows cvi8.0,gprs connection had been programmed,and udp test is ok )

对无线通信环境下的多径衰落和阴影衰落进行的建模。给出了一些仿真的建议(Modeling on multi-path effect and shadowing under wireless communication system. And this code gives some advice on simulation of these situation.)

说明：  EtherCAT(以太网控制自动化技技)是一种用于确定性以太网的高性能技业通信协议,它扩展了IEEE 802.3 以太网标准,使得数据传输中具有可预测性定时及高精度同步等特点。这个开放性标准作为 IEC 61158 的组成部分,常用于机械设计及运动控制等应用中。EtherCAT 采用标准的IEEE802-3 以太网帧,帧结构如图 1。EtherCAT 协议直接用标准以太网的帧格嵌传输数据,并不修改其基本结构(ethercat communication)

基于OPNET的IEEE80211战场WLAN增援救助仿真及性能评估(OPNET-based reinforcement of IEEE80211 battlefield WLAN simulation and performance evaluation assistance)

说明：  RA码的仿真程序，包括编码器、信道、译码器，参数可配置。(RA code simulation program, including encoder, decoder, channel, parameters can be configured.)

说明：  服务通讯程序，采用服务+客户端模式，有源代码可以自己修改研究(Services, communication procedures, using service+ client mode, the active code can modify their own research)

uC OS_II在DSP芯片TMS320F281x上的移植(OS_II embedded DSP chip in the transplant TMS320F281x)